Fabrication and Characterization of a Conductive Proton Exchange Membrane Based on Sulfonated Polystyrenedivinylbenzene Resin-Polyethylene (SPSDR-PE): Application in Direct Methanol Fuel Cells

Document Type : Research Article

Authors

1 Department of Applied Chemistry, University of Gonabad, Gonabad, I.R. IRAN

2 Department of Applied Chemistry, University of Sistan and Baluchestan, Zahedan, I.R. IRAN

3 Department of Applied Chemistry, University of Sistan and Baluchestan, P.O. Box 98135-674 Zahedan, I.R. IRAN

4 Polymer Research Laboratory, University of Sistan and Baluchestan, Zahedan, I.R. IRAN

5 Department of Inorganic Chemistry, University of Sistan and Baluchestan, Zahedan, I.R. IRAN

Abstract

A novel proton exchange membrane has been prepared using sulfonated poly(styrene-divinylbenzene) resin(SPSDR)–polyethylene(PE). The membrane is characterized by FT-IR, SEM and TGA/DSC. Water uptake, oxidative resistance, ionic conductivity and methanol permeability are measured to evaluate its performance in a direct methanol fuel cell. The on-set degradation temperature of the SPSDR is above 120°C. The membranes were confirmed to retain 1–5% water vapor at 80–140 °C in the air due to the hydrophily of highly sulfonated polystyrene. The ionic conductivity and permeability of the membrane to methanol was found to increase with temperature without extra humidity supply.A direct methanol fuel cell was designed and assembled with the suggested SPSDR-PE membrane. The effect of some experimental factors such as temperature, methanol concentration, and flow rate as well as NaOH concentration on the electrical performances of fuel cells was studied and optimized.

Keywords

Main Subjects


[1] Zhang L., Chae S-R., Hendren Z., Park J-S., Wiesner M.R., Recent Advances in Proton Exchange Membranes for Fuel Cell Applications, Chem. Eng. J., 204: 87–97 (2012).
[3] Kim D.J., Lee H.J., Nam S.Y., Sulfonated Poly(arylene ether sulfone) Membranes Blended with Hydrophobic Polymers for Direct Methanol Fuel Cell Applications, Int. J. Hydrogen Energy, 39: 17524-17532 (2013),.
[4] Zeng Q.H., Liu Q.L., Broadwell I., Zhu A.M., Xiong Y., Tu X.P., Anion Exchange Membranes Based on Quaternized Polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene for Direct Methanol Alkaline Fuel Cells, J. Membr. Sci., 349: 237–243 (2010).
[5] Sherazi T.A., Sohn J.Y., Lee Y.M., Guiver M.D., Polyethylene-based Radiation Grafted Anion-Exchange Membranes for Alkaline Fuel Cells, J. Membr. Sci., 441: 148–157 (2013).
[6] Liu W., Cai W., Liu C., Sun Sh., Xing W., Magnetic Coupled Passive Direct Methanol Fuel Cell: Promoted CO2 Removal and Enhanced Catalyst Utilization, Fuel, 139: 308-313 (2015).
[8] Li J., Wang J., Chen Xi., Lv Zh., Chen T., Wang T., A Highly Conductive Proton Exchange Membrane for High Temperature Fuel Cells Based on Poly(5-vinyltetrazole) and Sulfonated Polystyrene, Solid State Ionics, 255: 128-134 (2014).
[9] Cho M. K., Lee D-N., Kim Y-Y., Han J., Kim H-J., Cho E.A., Lim T-H., Henkensmeier D., Yoo S.J., Sung Y-E., Park S., Jang J.H., Analysis of the Spatially Distributed Performance Degradation of a Polymer Electrolyte Membrane Fuel Cell Stack, Int. J. Hydrogen Energy, 39: 16548-16555 (2014).
[10] Liu J., Laghrouche S., Ahmed F-Sh., Wack M., PEM Fuel Cell Air-Feed System Observer Design for Automotive Applications: An Adaptive Numerical Differentiation Approach, Int. J. Hydrogen Energy, 39, 17210-17221(2014).
[11] Hassan M.A., Kamarudin S.K., Loh K.S., Daud W.R.W., Sensors for Direct Methanol Fuel Cells, Renew. Sust. Energ. Rev., 40: 1060-1069 (2014).
[12] Luo Y., Jiao K., Jia B., Elucidating the Constant Power, Current and Voltage Cold Start Modes of Proton Exchange Membrane Fuel Cell, Int. J. Heat. Mass. Tran., 77: 489–500(2014).
[14] Hong-jun N., Cheng-jin Zh., Xing-xing W., Su-yang M., Ping L., Performance of Special-Shaped Direct Methanol Fuel Cell with Sol–Gel Flux Phase, J. Fuel Chem. Technol, 38(5): 604-609 (2010).
[15] Mekhilef S., Saidur R., Safari A., Comparative Study of Different Fuel Cell Technologies, Renew. Sust. Energ. Rev., 16: 981–989 (2012).
[16] Wang Y., Geder J., Schubert J.M., Dahl R., Pasel J., Peters R., Optimization of Adsorptive Desulfurization Pocess of Jet Fuels for Application in Fuel Cell Systems, Fuel Process. Technol., 95: 144–153(2012).
[18] Perrot C., Gonon L., Marestin C., Gebel G., Hydrolytic Degradation of Sulfonated Polyimide Membranes for Fuel Cells, J. Membr. Sci., 379: 207-214 (2011).
[19] Li Q., Jensen J.O., Savinell R.F., Bjerrum N.J., High Temperature Proton Exchange Membranes Based on Polybenzimidazoles for Fuel Cells, Prog. Polym. Sci., 34: 449–477(2009).
[20] Zhong S., Cui X., Dou S., Liu W., Gao Y., Hong B., Improvement in Silicon-Containing Sulfonated Polystyrene/Acrylate Membranes by Blending and Crosslinking, Electrochim. Acta, 55: 8410–8415 (2010).
[21] Abdrashitov E.F., Bokun V.Ch., Kritskaya D.A., Sanginov E.A., Ponomarev A.N., Dobrovolsky Y.A., Synthesis and Properties of the PVDF-Based Proton Exchange Membranes with Incorporated Cross-Linked Sulphonatedpolystyrene for Fuel Cell, Solid State Ionics, 251: 9-12 (2013).
[22] Díaz M., Ortiz A., Ortiz I., Progress in the Use of Ionic Liquids as Electrolyte Membranes in Fuel Cells, J. Membr. Sci., 469: 379-396 (2014).
[23] Díaz M., Ortiz A., Isik M., Mecerreyes D., Ortiz I., Highly Conductive Electrolytes Based on Poly([HSO3 BVIm][TfO])/[HSO3-BMIm][TfO] Mixtures for Fuel Cell Applications, Int. J. Hydrogen Energy, 40(34): 11294–11302 (2015).
[24] Ahmad H., Kamarudin S.K., Hasran U.A., Daud W.R.W., Overview of Hybrid Membranes for Direct-Methanol Fuel-Cell Applications, Int. J. Hydrogen Energy, 35: 2160-2175 (2010).
[25] Xie Z., Song C., Andreaus B., Navessin T., Shi Z., Zhang J., Holdcroft S., Discrepancies in the Measurement of Ionic Conductivity of PEMs Using Two- and Four-Probe AC Impedance Spectroscopy, J. Electrochem. Soci., 153(10) : 173-178 (2006).
[26] Khorasani-Motlagh M., Noroozifar M., Ekrami-Kakhki M-S, Investigation of the Nanometals (Ni and Sn) in Platinum Binary and Ternary Electrocatalysts for Methanol Electrooxidation0i Int. J. Hydrogen Energy, 36: 11554-11563 (2011).
[27] Ahmad H., Kamarudin S.K., Hasran U.A., Daud W.R.W., A Novel Hybrid Nafion-PBI-ZP Membrane for Direct Methanol Fuel Cells, Int. J. Hydrogen Energy, 36: 14668-14677 (2011).
[28] Wang C.-H., Chen C.-C., Hsu H.-C., Du H.-Y., Chen C.-P., Hwang J.-Y., Chend L.C., Shih H.C., Stejskal J., Chen K.H., Low Methanol-Permeable Polyaniline/Nafion Composite Membrane for Direct Methanol Fuel Cells, J. Power Sources, 190: 279-284 (2009).
[29] Mishraa A.K., Boseb S., Kuilab T., Kimc N.H., Lee J.H., Silicate-Based Polymer-Composite Membranes for Polymer Electrolyte Membrane Fuel Cells, Prog. Polym. Sci., 37: 842– 869(2012).
[30] Mehdi S., Khaleghi H., Mirzaei M., Parametric Study of Operation and Performance of a PEM Fuel Cell Using Numerical Method, Iran. J. Chem. Chem. Eng. (IJCCE), 27(2): 1-12 (2008).
[32] Ni H-J., Zhang Ch-J., Wang Xi-Xi., Ma Su-Y., Liao P., Performance of Special-Shaped Direct Methanol Fuel Cell with Sol-Gel Flux Phase, J. Fuel. Chem. Technol., 38: 604-609(2010).
[33] Chen C.Y., Garnica-Rodriguez J.I., Duke M.C., Dalla Costa R.F., Dicks A.L., Diniz da Costa J.C., Nafion/Polyaniline/Silica Composite Membranes for Direct Methanol Fuel Cell Application, J. Power Sources, 166: 324-330(2007).